02 · ASTM G21

Snap Plate Mold Defender™

Sprayed over the snapped lines and the bottom of every plate before the walls stand. The one surface nobody can reach again, defended in about an hour.

Water repellent, mildewcide and mold defender for the one surface on the job nobody can reach again. Snap your lines as usual, roll three inches wide of the line, coat the bottom of each plate on the deck, stand the walls. Single application, roller or sprayer, no change to layout. NorCal Lumber and West Coast Framing use it on every project they build together.

  • ASTM G21 tested
  • Non-toxic, very low VOC
  • About an hour per house
  • Crew you already have
Framed room with every bottom plate and the first twelve inches of stud treated blue with Snap Plate Mold Defender
The short answer

Snap Plate Mold Defender™ is a construction mold defender for the bottom plate: a water repellent, mildewcide and mold inhibitor in one coat, rolled over the snapped layout lines and the underside of every plate before the walls are stood. It is tested to ASTM G21, applied by the framing crew with a roller or sprayer, and changes nothing about layout.

Why the plate line

Trapped moisture under a bottom plate does not dry out.

Rain and snow land on the deck during framing and collect under the bottom plates. Vertical lumber dries. The underside of a plate sitting on a wet subfloor does not, and once the walls are stood and the drywall is on, nobody can reach it again.

Snap Plate Mold Defender™ is a commercial strength spray-on formula that creates a moisture and fungi defense on the wood it touches. Applied under, around and on the wall plates and subfloor at layout, it defends the plate line before the building is closed in.

What it does
Prevents trapped moisture
Defends wood bottom plates and subfloors under walls.
Resists fungal growth
Proven to defend a wide variety of fungal organisms.
Non-toxic, very low VOC
A free flowing dispersion that is safe indoors and during application.
ASTM G21 tested
Passed laboratory testing to prove resistance to fungal and mold growth.

How the crew applies it

Best results start with lumber and subfloors that are not wet. No change to layout.

1Layout crew applying Snap Plate Mold Defender along the snapped wall lines
Spray the snapped lines
At layout, spray a 12" coating over the snapped wall lines before the walls go vertical.
2Stack of prefabricated wall panels with treated bottom plates
Treat the plates
Coat the bottom of each plate on the deck. Factory prefab walls get their plates sprayed before leaving the plant.
3Close-up of a standing wall with its bottom plate and studs treated blue
Stand the walls, spray the base
Spray the bottom of the standing walls up six inches and 12" out onto the floor sheathing for additional defense.
Five gallon pail of Snap Plate Mold Defender beside the FireProShop battery sprayer

One pail, one sprayer, about an hour.

With the FireProShop battery powered 4 gallon backpack sprayer, one pail treats the plate line on a typical house in about an hour, with the crew you already have. Comes in 1, 5 and 55 gallon sizes.

Ask about pricing and sprayers
Specifications
Test standardASTM G21
ApplicationRoller or sprayer, single coat
WhereSnapped lines & plate bottoms
Sizes1 · 5 · 55 gallon

Treat the plate line on your next house.

NorCal Lumber and West Coast Framing use it on every project they build together, and prefab walls from NorCal Lumber ship with the plates already treated. Tell Steve the house count and framing date and he will call back with numbers.

FAQ

Questions about Snap Plate Mold Defender™.

What is a construction mold defender?
A treatment applied during framing to the surfaces that will trap moisture after the walls go up and cannot be reached again. Snap Plate Mold Defender is made for the plate line: the snapped layout lines on the deck and the bottom of every plate.
Why treat the bottom plate specifically?
Rain and snow land on the deck during framing and collect under the bottom plates. Once the walls are stood and the drywall is on, the underside of the plate is the one surface on the job nobody can reach again, so water that gets there stays there.
How is Snap Plate Mold Defender applied?
Snap your lines as usual, roll three inches wide of the line, coat the bottom of each plate while it is on the deck, and stand the walls. One coat, roller or sprayer. The extra width past the plate footprint is what interrupts horizontal moisture movement into the plate.
How much do I need for a house?
One pail and one sprayer treat the plate line on a typical house in about an hour. Send the plan or the house count with your inquiry and Steve will size the order, including the sprayer if you need one.
Does it slow down framing?
No. It is about an hour on a typical house, done at layout, and the walls go vertical on the same schedule. Framers using it report no change to how their crews frame.
What test standard is behind it?
ASTM G21, the standard practice for determining the resistance of synthetic polymeric materials to fungi.
Who applies it, and what sizes does it come in?
The framing crew you already have. FireProShop shows them the method, and prefabricated walls from NorCal Lumber ship with the plates already treated. It comes in 1, 5 and 55 gallon sizes.
Is it safe for the crew and for occupied spaces?
Yes. It is non-toxic with very low VOC, a free flowing dispersion that is safe indoors and during application. No respirators or special handling beyond normal jobsite practice.

Related reading

All news →
Product inquiry

Ask about Snap Plate Mold Defender™.

Quantity, timing, jobsite. Steve will call you back with numbers and a straight answer on fit.

Attach plans or a lumber list (optional)
PDF, photos, or common office files. Up to 25 MB.
Write and Steve will call you.
Or call directly
Steve Conboy
Inventor & Founder · FireProShop
Need the whole package?
Send us the framing package and we will price every layer at once.
Request a quote
Snap Plate Mold Defender™

Other products